Huntron Tracker Model 30

Features:

Add the benefits of Power-Off test to your current diagnostic test strategy

Match the circuit impedance by setting the applied voltage, frequency and source resistance

Interface to the Huntron Access Prober , Scanner 31S or Scanner II

Use Huntron Workstation software for test creation and signature storage

Description:

The Huntron Tracker Model 30 is a new compact Tracker designed for use with Huntron Workstation and accessories such as the New Scanner II, the new Scanner 31S or an Huntron Access Prober. Take advantage of Tracker Signature Analysis capabilities to help you troubleshoot printed circuit board (PCB) faults to the component level and without applying power, saving circuits from possible further damage.

The Tracker Model 30 enables the user to set the applied voltage, frequency and source resistance to best match the circuit characteristics and display the optimum Tracker signature. The power of Huntron Workstation allows for the creation of Tracker Model 30 test routines and signature storage.

The Huntron Tracker Model 30 is controlled by the Huntron Workstation 4 software for test database creation and signature capture. Signatures from known good PCBs are stored in the test database and used for comparison when troubleshooting suspect PCBs. Interfacing the Huntron Tracker Model 30 to test points can be accomplished manually using Huntron Microprobes, Scanner 31S, Scanner II , or automatically when used with a Huntron Robotic Prober such as the Huntron Access USB Prober . ( USB connection to pc for storage and display)

Included Accessories

MP20 Microprobes

Part number 98-0249

Manual on CD

Part number 06-5217

Huntron ASA Training Course

Part number 98-0515

2 Common leads

Part number 98-0043

Workstation software

Part number 98-0463

Power cord

Part number 98-0015

10K ohm jumper lead

Part number 98-0028

1K ohm jumper lead

Part number 98-0029

USB cable

Part number 98-0418

Specifications- Tracker Model 30

ELECTRICAL

(Note: Test Signal is a sine wave.)

Open Circuit Voltage (Vs):

24 selections of peak voltage:

200mV, 400mV, 600mV, 800mV, 1V to 20V in 1V steps including 10V (Low), 15V (Med 1), 20V (Med 2)

Source Resistance (Rs):

16 selections of resistance:

10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, 54Ω (Low), 1.2kΩ (Med 1), 26.7kΩ (Med 2)

Frequency (fs):

40 selections of frequency:

20Hz to 190Hz in 10Hz steps; 200Hz to 1.9kHz in 100Hz steps; 2kHz to 5kHz in 1kHz steps

Connections

BNC (Ch. A; Ch. B; Com.), banana (Ch. A; Ch. B; Com.)

Auxillary Connection

9 pin mini jack with ground, Trigger IN, Trigger OUT, Calibration TP, Sine wave zero-crossing, Signal ON, Line IN and Line OUT

GENERAL

Part Number

99-0392

Dimensions

11.1in W x 1.8in H x 8.6in D

(28.2cm W x 4.6cm H x 21.8cm D)

Warranty

1 year limited

Certifications

CE and ETL listed

Optional Accessories for Tracker Model 30

Footswitch for Tracker Model 30 -
Part# 98-0315

This Footswitch will allow you to increment tests using the manual test probes where your hands are not free to access the PC keyboard or mouse. This Footswitch will also work with the TrackerPXI. Very useful!

Scanner II for Tracker Model 30 -
Part# 99-0393
Dual Channel Scanner accessory for the Tracker Model 30. It allows for multiple pin scanning with cable interfaces such as custom cables or IC clips.

Scanner 31S for Tracker Model 30 -
Part# 99-0393
Single channel Scanner accessory for the Tracker Model 30. It allows for multiple pin scanning with cable interfaces such as custom cables or IC clips.

Visit to the Huntron Support Forum. In an ongoing effort to make support more accessible, this forum added to the Huntron web site for the benefit of Huntron users worldwide.

For further information, please click here

| TOP |